91400 RM (IM) HK No.6688-1/23
Ver.1.01
22699
Preliminary
Overview
The LC86P5632 is a CMOS 8-bit single chip microcontroller with one-time PROM for the LC865600 series.
This microcontroller has the function and the pin description of the LC865600 series mask ROM version, and 32K-byte
PROM.
DIP/QFP package are available for shipping as well as LC865600 series. It is suitable to set up first release, prototyping,
developing and testing of set.
Features
(1) Option switching by PROM data
The option function of the LC865600 series can be specified by the PROM data.
LC86P5632 can be checked the function of the trial pieces using the mass production board.
(2) Internal one-time PROM capacity
: 32768 bytes
(3) Internal RAM capacity
: 512 bytes
Used PROM or RAM capacity are equal ROM or RAM capacity of mask ROM version which applies LC86P5632.
Mask ROM version
PROM capacity
RAM capacity
LC865632
32512 bytes
512 bytes
LC865628
28672 bytes
512 bytes
LC865624
24576 bytes
512 bytes
LC865620
20480 bytes
384 bytes
LC865616
16384 bytes
384 bytes
LC865612
12288 bytes
384 bytes
LC865608
8192 bytes
384 bytes
Programming service
We offers various services at nominal charges. These include the ROM writing, the ROM reading, the package stamping
and the screening. Contact our representative for further information.
8-Bit Single Chip Microcontroller
with One-Time Programmable PROM
LC86P5632
Ordering number : ENN*6688
CMOS IC
LC86P5632
No.6688-2/23
(4) Operating supply voltage
: 4.5V to 6.0V
(5) Instruction cycle time
: 0.98
s to 400
s
(6) Operating temperature
: -30
C to +70
C
(7) The pin and the package compatible with the LC865600 series mask ROM devices
(8) Applicable mask ROM version
: LC865632/ LC865628/ LC865624/LC865620/LC865616/
LC865612/
LC865608
(9) Factory shipment
: DIP64S, QFP64E
Notice for use
LC86P5632 is provided for the first release and small shipping of the LC865600 series.
At using, take notice of the followings.
(1) A point of difference LC86P5632 and LC865600 series
Item LC86P5632
LC865632/28/24/20/16/12/08
Port form at reset
Please refer "Port form at reset " on next page.
Operation after reset
releasing
The option is specified until 3ms
after going to a `H' level to the reset
terminal by dgrees. The program
is executed from 00H of the
program counter.
The program is executed from 00H of
the program counter immediately after
going to a `H' level to reset terminal.
Operating supply voltage
range (VDD)
4.5V to 6.0V
2.7V to 6.0V
Total output current
[
IOAH(1)]
[
IOAH(2)]
Power dissipation
[IDDOP(1)]
[IDDOP(2)]
[IDDOP(3)]
[IDDOP(4)]
Refer to `electrical characteristics' on the semiconductor news.
A kind of the option corresponding of the LC86P5632
A kind of option
Pins, Circuits
Contents of the option
Port 0
(Specified in a bit)
1. Input : No pull-up MOS Tr.
Output : N-channel open drain
2. Input : Pull-up MOS Tr.
Output : CMOS
Port 1,2
(Specified in a bit)
1. Input : Programmable pull-up MOS Tr.
Output : N-channel open drain
2. Input : Programmable pull-up MOS Tr.
Output : CMOS
Input/output form of
Input/output ports
Port 3,4,5
(Specified in a bit)
1. Input : No Programmable pull-up MOS
Tr.
Output : N-channel open drain
2. Input : Programmable pull-up MOS Tr.
Output : CMOS
Pull-up MOS Tr. Of port7
port7
(Specified in a bit)
1. Pull-up MOS Tr. not provided
2. Pull-up MOS Tr. provided
*
P74
has on pull-up resistor option.
The port operation related the option is different at reset. Refer to the next table.
LC86P5632
No.6688-3/23
Port form at reset
Pin
Contents of the option
LC86P5632
LC865632/28/24/20/16/12/08
Input : Not pull-up MOS Tr.
Output : N-channel open drain
(Same as the mask version)
Input mode without pull-up
MOS Tr. (Output is OFF)
P0
Input : Pull-up MOS Tr.
Output : CMOS
Input mode
The pull-up MOS Tr. is not provided
during reset or several hundred
microseconds after releasing reset.
After that, the pull-up MOS Tr. is
provided. (Output is OFF)
Input mode without pull-up
MOS Tr. (Output is OFF)
Input :
Programmable
pull-up
MOS Tr.
Output : N-channel open
drain
(Same as the mask version)
Input mode without pull-up
MOS Tr. (Output is OFF)
P1,
P2
Input :
Programmable
pull-up
MOS Tr.
Output : CMOS
(Same as the mask version)
Input mode without pull-up
MOS Tr. (Output is OFF)
Input :
Not
Programmable
pull-up MOS Tr.
Output : N-channel open drain
(Same as the mask version)
Input mode without pull-up
MOS Tr. (Output is OFF)
P3,
P4,
P5
Input :
Programmable
pull-up
MOS Tr.
Output : CMOS
(Same as the mask version)
Input mode without pull-up
MOS Tr. (Output is OFF)
Pull-up MOS Tr. not provided
(Same as the mask version)
Input mode without pull-up
MOS Tr.
P7
Pull-up MOS Tr. provided
Input mode
The pull-up MOS Tr. is not provided
during reset or several hundred
microseconds after releasing reset.
After that, the pull-up MOS Tr. is
provided.
Input mode without pull-up
MOS Tr.
(2) Option
LC86P5632 uses 256 bytes which is addressed on 7F00H to 7FFFH in the program memory as option data area. This
area does not affect the execution of program but the program memory capacity of LC865632 is 32512 bytes which is
addressed on 0000H to 7EFFH.
The option data is created by the option specified program "SU865000.EXE". The created option data is linked to the
program area by linkage loader "L865000.EXE".
LC86P5632
No.6688-4/23
(3) ROM space
(4) Ordering information
1. When ordering the identical mask ROM and PROM devices simultaneously.
Provide an EPROM containing the target memory contents together with the separate order forms for each of the
mask ROM and PROM versions.
2. When ordering a PROM device.
Provide an EPROM containing the target memory contents together with an order form.
How to use
(1) Specification of option
Programming data for PROM of the LC86P5632 is required.
Debugged evaluation file (EVA file) must be converted to an INTEL-HEX formatted file (HEX file) with file converter
program, EVA2HEX.EXE. The HEX file is used as the programming data for the LC86P5632.
(2) How to program for the PROM
LC86P5632 can be programmed by the EPROM programmer with attachment ; W86EP5032D,
W86EP5032Q.
Recommended EPROM programmer
Productor EPROM
programmer
Advantest
R4945, R4944, R4943
Andou AF-9704
AVAL PKW-1100,
PKW-3000
Minato electronics
MODEL 1890A
"27512 (Vpp=12.5V) Intel high speed programming" mode available. The address must be set to
"0000H to 7FFFH" and a jumper (DASEC) must be set to `OFF' at programming.
(3) How to use the data security function
"Data security" is the disabled function to read the data of the PROM.
The following is the process in order to execute the data security.
1. Set `ON' the jumper of attachment.
2. Program again. Then EPROM programmer displays the error. The error means normally activity of the data
security. It is not a trouble of the EPROM programmer or the LSI.
7FFFH
7F00H
7EFFH
6FFFH
5FFFH
4FFFH
3FFFH
2FFFH
1FFFH
0000H
Program area
32K bytes
Option data
area 256 bytes
LC865632
Program area
28K bytes
Option
Data Area
LC865628
Program area
24K bytes
Option
Data Area
LC865624
Program area
20K bytes
Option
Data Area
LC865620
Program area
16K bytes
Option
Data Area
LC865616
Program area
12K bytes
Option
Data Area
LC865612
Program area
8K bytes
Option
Data Area
LC865608
LC86P5632
No.6688-5/23
Notes
Data security is not executed when the data of all address have `FF' at the sequence 2 above.
The programming by a sequential operation "BLANK
PROGRAM
VERIFY" cannot be executed data security at the
sequence 2 above.
Set to `OFF' the jumper after executing the data security.
W86EP5032D
W86EP5032Q
Data security
Not data security
Data security
Not data security
1 pin
1 pin mark
of LSI
1 pin
PDF 
ZIP